What's The Max Inlet Diameter A 300 mm Drum Chipper Can Actually Swallow?

Nov 13, 2026 Leave a message

The gap between the number on the nameplate and the log that fits in the throat
There is a seductive piece of bad math that nearly every first-time chipper buyer makes.You see"300 mm drum chipper"and your brain hears"takes a 300 mm log."Twelve inches of tree,straight into the hopper.
It doesn't.Not even close.And the reason is one of the most expensive misunderstandings in small-scale wood processing.
The number on the box describes the drum,not the door
On a drum chipper,the headline figure-300 mm,500 mm,600 mm,800 mm-is almost always the diameter of the cutting rotor(the spinning cylinder the knives are bolted to),not the size of the hole you feed wood through.These two dimensions are related,but they are emphatically not the same number,and reputable builders now print them as separate spec lines precisely because buyers keep confusing them.
Take the Chinese BX series,which supplies most"300 mm"machines on the global market.The smallest model,the BX213,carries a 300 mm rotor.Its feed inlet measures only 120 mm tall by 300 mm wide.The manufacturer rates it for a maximum log diameter of just 90 mm-about 3.5 inches-driven by a 30 kW motor.Step up to the BX215 with a 500 mm rotor:the inlet grows to 140 by 400 mm,the rated log jumps to 105 mm,and the motor climbs to 45 kW.The BX216,with a 600–650 mm rotor,opens to 180 by 500 mm and handles 120–150 mm logs on 55 kW.At the top of the common range,the BX218 uses an 800 mm rotor,a 225 by 680 mm opening,and a 110 kW motor to process logs up to 160–200 mm.Parallel models from TCPEL and GTC confirm the same pattern-for example,the TC218 lists a 350 by 700 mm feeding opening but states a maximum log diameter of 300 mm,and the builder explicitly warns that"feeding opening is the machine opening and is not the same as maximum log diameter."
Read that bottom line again.A 300 mm drum chipper is a~90 mm(3.5-inch)log chipper.The throat is only 120 mm tall,and the machine is rated for a log roughly 25%smaller than that opening-before you even account for the real world.
Why the throat eats its own capacity
Three separate geometries shave the nominal opening down to the rated log.
First,inlet height is the hard ceiling.Wood enters horizontally.A 120 mm-tall slot simply cannot pass a 120 mm round without the top feed-roll housing lifting-and on a BX213-class machine that housing is fixed or spring-loaded,not hydraulically floated.The log has to clear the lower roll,the anvil(bed knife)gap,and the roll above it.That stack eats roughly 30 mm immediately.
Second,the bite angle.A feed roll can only pull a cylinder if the contact point sits inside the friction angle-roughly 16 to 20 degrees for knurled steel on bark.Past that,the roll slips and the log just sits there smoking.In practice this caps reliable bite at about 0.7 to 0.8 times the roll-gap envelope,which is exactly why a 120 mm inlet pencils out to a~90 mm rating.
Third,power,not just opening.A 300 mm-rotor machine turns over 30 to 40 kW(40 to 55 HP).Industry sizing tables put a true 150 mm(6-inch)throat at a minimum of 67 to 99 HP.You could weld the inlet of a BX213 open to 150 mm and it still wouldn't eat a 6-inch oak-the drum would bog,the belts would glaze,and the key would shear.The opening was never the only limit;torque was.
The 80%rule,and what"rated"really means
Every manufacturer's max-diameter number is quoted against straight,green,small-end-first softwood-the laboratory specimen of the logging world.The moment reality shows up,you derate.
For a 300 mm(BX213)drum,the comfortable maximum on green pine or poplar that is dead straight is indeed the rated 90 mm ceiling.With mixed green hardwood that has a slight sweep,that drops to 70–80 mm(roughly 2.75 to 3.15 inches).Seasoned oak or hickory with small knots pushes it further down to 65–75 mm.Frozen hardwood or a forked butt log forces you down to 50–65 mm-or you simply do not feed it.Crotches,butt flares,and root balls should be trimmed first or avoided entirely.
The standing rule across chipper-safety training is never feed above 80%of the rated diameter,and treat the rated number as a peak,not a diet.Independent reviews of comparable 6-inch-class drum machines say the same thing in plain English:six inches is the peak rated capacity,not sustained throughput;the comfortable working range is four to five inches;treat the six-inch number as a ceiling for occasional limbs.Scale that ratio down and a 90 mm-rated 300 mm drum wants 70 mm material on a normal Tuesday.
The geometry tax nobody puts in the brochure
Four things quietly steal another 10 to 20 percent off the top on any given shift.
•Sweep and taper.A 90 mm log with a banana curve presents as a 110 mm chord at the throat.It bridges,hangs up,and hand-feeding it past the roll is how fingers get lost.
•Knots and forks.A fork is two logs pretending to be one.The self-feeding drum grabs one tine,the other jams the housing,and you are reaching for the kill switch.
•Knife sharpness and anvil gap.A dull blade does not cut-it crushes,which spikes drum load and turns a 75 mm log into a stall.New knives recover most of the rated capacity;20 hours past due,they do not.
•Roll condition.Worn or glazed feed rolls lose bite angle.A machine that swallowed 85 mm green ash in April may top out at 70 mm in November with the same wood and the same operator.
How to read the next chipper nameplate you see
Ignore the marketing headline.Hunt for these four specifications,in this order.
First,feed inlet height and width-the real doorway.For a BX213 that is 120 by 300 mm.Second,maximum process log diameter-the engineered answer.If it is missing,multiply the inlet height by 0.75 and you will be close.Third,main motor kilowatts or horsepower-cross-check against the sizing table.A"300 mm"machine under roughly 40 HP is a 3-inch chipper wearing a big label.Fourth,feed system type-gravity/self-feed versus hydraulic top roll.Hydraulic float is what lets you use the rated diameter on crooked wood;without it,derate another 15 percent.
Bottom line
A 300 mm drum chipper-the BX213/300-rotor class that dominates the small industrial and farm-steeplechase market-will physically accept a 120 mm slot,is rated for a 90 mm(3.5-inch)straight green log,and will happily live its whole life at 70–80 mm(about 3 inches)of mixed hardwood.Push it past that regularly and you are not"getting your money's worth"-you are buying belts,keys,and possibly a new drum bearing.
The 300 mm in the name is how wide the knife cylinder is.The log it swallows is closer to one-third of that.Size your expectations-and your infeed conveyor-accordingly.
Sources include manufacturer data from TCPEL,Gongyi Chenhong,and Fude Machinery,along with independent reviews and safety guidelines from VDOT and industry sizing tables.